Remove the Fitting.
Save the Pipe.
The Pinell Tools 1‑1/4 inch PVC Hub Remover is a patented, drill‑powered plumbing repair tool that removes glued 1‑1/4 inch PVC fittings while saving the original pipe. Instead of cutting back pipe, stacking extra couplings, and opening up walls, ceilings, or slabs, this pipe‑saving hub remover shaves the fitting out from the inside so you can reuse the existing 1‑1/4 inch PVC and complete clean, in‑line repairs in minutes.
Designed for 1‑1/4 inch drain, vent, pool, spa, and specialty lines, the cutter reaches fittings that sit tight to framing, concrete, or sheetrock—places where a saw, multi‑tool, or traditional socket saver either can’t reach or risks damaging the pipe. Chuck it into a standard drill and you can remove a 1‑1/4 inch PVC hub without cutting the pipe, avoiding unnecessary demolition, extra fittings, and time‑consuming rework on every repair.
Key features and benefits:
-
Size‑specific 1‑1/4 inch PVC hub remover for glued fittings
-
Removes the fitting itself and saves the pipe for a fresh solvent weld
-
Drill‑powered design for fast, controlled hub removal in tight spaces
-
Works where traditional PVC fitting reamers and socket savers can’t reach
-
Ideal for repairs in walls, slabs, pump rooms, equipment pads, and tight chases
-
Reduces demolition, patching, and material waste on every 1‑1/4 inch PVC repair
This is the tool plumbers and service techs reach for when a 1‑1/4 inch PVC elbow, coupling, or tee is tight to drywall, close to a slab, or buried in equipment piping that would be a nightmare to rebuild—because fixing one fitting shouldn’t mean re‑piping the entire run.
-
Size-Specific PrecisionEngineered specifically for this PVC hub size — not a one-size-fits-all tool.
-
Removes the Fitting, Saves the PipeShaves the glued fitting out from the inside, leaving a clean hub ready for a new solvent weld.
-
Drill-PoweredMounts in any standard power drill — corded or cordless. No special equipment needed.
-
Works in Tight SpacesReaches fittings flush to walls, ceilings, cabinets, and slabs where saws and multi-tools can't safely operate.
-
Reduces Demo & Material WasteNo extra couplings, no patching, no unnecessary demolition — just a targeted repair that protects your time and margin.
-
Anodized Aluminum ConstructionBuilt for the trade — corrosion-resistant, lightweight, and tough enough for daily use on job sites.
| Pipe Size | 1¼″ PVC |
| Drive / Shank | 7/16″ Hex |
| Compatible Pipe | Schedule 40 PVC & ABS |
| Not Compatible With | Schedule 80 PVC |
| Drive Type | Standard power drill (corded or cordless) |
| Material | Anodized Aluminum |
| Origin | Made in USA |
| Warranty | Lifetime |
Watch How It Works
See exactly how the Hub Remover cuts out a glued PVC fitting from the inside — leaving the pipe intact and ready for a new solvent weld. No cutting, no grinding, no wasted pipe.
Shop All Sizes →1-1/4" Hub Remover — FAQ
Everything you need to know about removing PVC hub fittings without cutting the pipe.
How do I remove a 1¼″ glued PVC fitting without cutting the pipe? +
The 1¼″ PVC Hub Remover mounts in a standard drill and cuts from inside the glued fitting, shaving out the hub while preserving the existing pipe. That lets you remove the 1¼″ fitting without cutting the pipe, so you can glue in a new fitting and keep the original run in place.
Where is the 1¼″ Hub Remover most useful? +
It's especially useful on 1¼″ drain lines, vent stacks, and larger supply runs — particularly where fittings are glued into walls, ceilings, or concrete and there's limited pipe exposed to work with. The tool lets you address the hub directly without tearing into the surrounding structure.
What's the difference between this and a traditional PVC socket saver or reamer? +
Traditional socket savers remove pipe from inside a fitting to reuse the fitting — they require extra pipe to cut back. This tool removes the fitting itself and saves the 1¼″ pipe, which is the right approach when the pipe stub is too short or too embedded to cut and couple without major demolition.
Will the 1¼″ Hub Remover damage the pipe or weaken the joint? +
The cutter is engineered to engage only the glued fitting wall, not the pipe itself, leaving a clean, round surface ready for a new solvent-welded connection. Used correctly in a standard drill, it preserves pipe integrity and creates a hub ready for a precise 1¼″ PVC repair.
Who is the 1¼″ PVC Hub Remover designed for? +
It's built for professional plumbers and contractors working on 1¼″ drain, vent, and supply piping in residential and commercial settings. When a hub repair needs to be fast, clean, and non-destructive, this tool eliminates the need to cut back pipe or open up finished surfaces.
Still have questions? Our team is based in Houma, Louisiana and knows these tools inside and out.
Contact Us →Three Steps. No Torch. No Damage.
Attach to your drill and done in minutes.
Insert the Hub Remover into any standard power drill — no special equipment needed.
Place the tool inside the hub fitting and engage your drill. The patented blade geometry does the work.
The fitting separates cleanly — the pipe stays undamaged and ready to accept a new fitting.
Save More with a Set
Bundle the sizes you need most and save on every job.
Includes: 1½″, 2″ & 3″ Hub Removers
Includes: 1½″, 2″, 3″ & 4″ Hub Removers + waterproof/shockproof case
Includes: All 8 sizes (½″–4″) + waterproof/shockproof case
Need a Different Size?
All 8 sizes available — pick yours.
