Remove the Fitting.
Save the Pipe.
The Pinell Tools 1‑1/2 inch PVC Hub Remover is a patented, drill‑powered plumbing repair tool that removes glued 1‑1/2 inch PVC fittings while saving the original pipe. Instead of cutting back pipe, stacking extra couplings, and opening up walls, ceilings, or slabs, this pipe‑saving hub remover shaves the fitting out from the inside so you can reuse the existing 1‑1/2 inch PVC and complete clean, in‑line repairs in minutes.
Designed for 1‑1/2 inch drain, waste, vent, pool, spa, and branch lines, the cutter reaches fittings that sit tight to framing, concrete, or sheetrock—places where a saw, multi‑tool, or traditional socket saver either can’t reach or risks damaging the pipe. Chuck it into a standard drill and you can remove a 1‑1/2 inch PVC hub without cutting the pipe, avoiding unnecessary demolition, extra fittings, and time‑consuming rework on every repair.
Key features and benefits:
-
Size‑specific 1‑1/2 inch PVC hub remover for glued fittings
-
Removes the fitting itself and saves the pipe for a fresh solvent weld
-
Drill‑powered design for fast, controlled hub removal in tight spaces
-
Works where traditional PVC fitting reamers and socket savers can’t reach
-
Ideal for repairs in walls, slabs, stacks, equipment pads, and tight chases
-
Reduces demolition, patching, and material waste on every 1‑1/2 inch PVC repair
This is the tool plumbers and service techs reach for when a 1‑1/2 inch PVC elbow, wye, or coupling is tight to drywall, close to a slab, or buried in equipment piping that would be a nightmare to rebuild—because fixing one fitting shouldn’t mean re‑piping the entire run.
-
Size-Specific PrecisionEngineered specifically for this PVC hub size — not a one-size-fits-all tool.
-
Removes the Fitting, Saves the PipeShaves the glued fitting out from the inside, leaving a clean hub ready for a new solvent weld.
-
Drill-PoweredMounts in any standard power drill — corded or cordless. No special equipment needed.
-
Works in Tight SpacesReaches fittings flush to walls, ceilings, cabinets, and slabs where saws and multi-tools can't safely operate.
-
Reduces Demo & Material WasteNo extra couplings, no patching, no unnecessary demolition — just a targeted repair that protects your time and margin.
-
Anodized Aluminum ConstructionBuilt for the trade — corrosion-resistant, lightweight, and tough enough for daily use on job sites.
| Pipe Size | 1½″ PVC |
| Drive / Shank | 7/16″ Hex |
| Compatible Pipe | Schedule 40 PVC & ABS |
| Not Compatible With | Schedule 80 PVC |
| Drive Type | Standard power drill (corded or cordless) |
| Material | Anodized Aluminum |
| Origin | Made in USA |
| Warranty | Lifetime |
Watch How It Works
See exactly how the Hub Remover cuts out a glued PVC fitting from the inside — leaving the pipe intact and ready for a new solvent weld. No cutting, no grinding, no wasted pipe.
Shop All Sizes →1-1/2" Hub Remover — FAQ
Everything you need to know about removing PVC hub fittings without cutting the pipe.
How do I remove a 1½″ glued PVC fitting without cutting the pipe? +
The 1½″ PVC Hub Remover mounts in a standard drill and cuts from inside the glued fitting, shaving out the hub while preserving the existing pipe. That lets you remove the 1½″ fitting without cutting the pipe, so you can glue in a new fitting and keep the original drain or vent line in place.
Where is the 1½″ Hub Remover most useful? +
It's most valuable on 1½″ P-traps, drain lines, and vent connections — one of the most common repair scenarios in residential plumbing. When a fitting under a sink, inside a wall, or near a floor drain is glued tight with no room to cut and couple, this tool lets you remove the hub without any demolition.
What's the difference between this and a traditional PVC socket saver or reamer? +
Traditional socket savers remove pipe from inside a fitting to reuse the fitting — they require extra pipe to cut back. This tool removes the fitting itself and saves the 1½″ pipe, which is the right approach when the stub is too short, too tight, or buried in a surface you don't want to open.
Will the 1½″ Hub Remover damage the pipe or weaken the joint? +
The cutter is engineered to engage only the glued fitting wall, not the pipe, leaving a clean, round surface ready for a new solvent-welded connection. Used correctly in a standard drill, it preserves pipe integrity and creates a hub that's ready for a proper 1½″ PVC repair.
Who is the 1½″ PVC Hub Remover designed for? +
It's built for professional plumbers, service techs, and experienced DIYers working on 1½″ drain, trap, and vent piping. It's one of the most-used sizes in the Hub Remover line because 1½″ drain repairs come up constantly — and this tool makes them fast, clean, and non-destructive.
Still have questions? Our team is based in Houma, Louisiana and knows these tools inside and out.
Contact Us →Three Steps. No Torch. No Damage.
Attach to your drill and done in minutes.
Insert the Hub Remover into any standard power drill — no special equipment needed.
Place the tool inside the hub fitting and engage your drill. The patented blade geometry does the work.
The fitting separates cleanly — the pipe stays undamaged and ready to accept a new fitting.
Save More with a Set
Bundle the sizes you need most and save on every job.
Includes: 1½″, 2″ & 3″ Hub Removers
Includes: 1½″, 2″, 3″ & 4″ Hub Removers + waterproof/shockproof case
Includes: All 8 sizes (½″–4″) + waterproof/shockproof case
Need a Different Size?
All 8 sizes available — pick yours.
